The Corn Snake Forum
The Corn Snake Forum
Home | Profile | Register | Active Topics | Members | Search | FAQ
Username:
Password:
Save Password
Forgot your Password?

 All Forums
 Corn Snake Posts
 Corn Snake - General Keeping information
 Habistat Heat mat question
 New Topic  Reply to Topic
 Printer Friendly
Author Previous Topic Topic Next Topic  

headlow
Hatchling

130 Posts

Posted - 30/03/2010 :  13:54:27  Show Profile  Reply with Quote
As already mentioned in a previous thread I'm having trouble with too high a hot end temperature in my 09 Corn's viv. Since I already have a heat mat and stat I've decided to switch, at least until the snake is big enough to go into a 3 foot viv.

My question is that on the instruction leaflet from Habistat it says to put the mat on top of some polystyrene. Is this nessacery?

Also do I rubber band the probes for the stat and thermometer together and weigh them down on top of the mat, or should the thermometer probe be on top of the substrate (which will be a very thin layer of aspen)?

1.0.0 Snow Corn

headlow
Hatchling

130 Posts

Posted - 30/03/2010 :  13:55:13  Show Profile  Reply with Quote
Sorry that should say too hot a cold end temperature!

Also I should have said it's going inside a 2 foot wooden viv.

1.0.0 Snow Corn

Edited by - headlow on 30/03/2010 14:00:10
Go to Top of Page

DannyBrown91
Fully Grown Corn

United Kingdom
3070 Posts

Posted - 30/03/2010 :  14:29:08  Show Profile  Click to see DannyBrown91's MSN Messenger address  Reply with Quote
The polystyreine is mainly for when they are outside a faun i think, it helps to insulate and send the heat where it is meant to go.

You could either rubberband them together or you could put the therm probe onto of the substarte but make sure that it is touching the substrate, with a thin layer of aspen it shouldn't make a difference.

0.0.1 Ghost Corn - Casper
0.0.1 Diffused Corn - Reggie
0.0.1 Amel Corn - Candy A.K.A Baby
1.0 Commom BCI - Rocky

0.1 Japanese Akita - Sasha

Location: Liverpool
Go to Top of Page

headlow
Hatchling

130 Posts

Posted - 30/03/2010 :  14:53:13  Show Profile  Reply with Quote
Cheers Danny. The little guy has just fed a few minutes ago, and I've ordered a low wattage daylight bulb (being in a converted attic it's quite dark) so once that's arrived and he's cleared himself out I'll get the mat rigged up.

1.0.0 Snow Corn
Go to Top of Page

n/a
deleted

110 Posts

Posted - 30/03/2010 :  21:56:01  Show Profile  Reply with Quote
quote:
The polystyreine is mainly for when they are outside a faun i think, it helps to insulate and send the heat where it is meant to go.

Would covering the polystyrene aswell in tin foil in order to reflect the heat up work or would it damage the heat mat by causing it to get to hot.


Go to Top of Page

Sta~ple
qeeun speler

United Kingdom
6129 Posts

Posted - 30/03/2010 :  22:25:05  Show Profile  Click to see Sta~ple's MSN Messenger address  Reply with Quote
If it's going in a wooden viv does it need to be insulated? I thought that was only for glass vivs.



A very special super, duper thanks for K :3
Go to Top of Page

morph2010
Egg

United Kingdom
97 Posts

Posted - 30/03/2010 :  22:48:47  Show Profile  Reply with Quote
i have a habistat mat in my wooden viv with the sensor and probe banded together, it stays at a steady 29-30 with a thin layer of substrate over the mat

1 Harley, Anery corn (not sure on age!)
1 Amber, Mad as a hatter springer 7yrs
8 ft fish tanks loads of fishys
1 Bobby, Cat 2yrs


Go to Top of Page

n/a
deleted

124 Posts

Posted - 30/03/2010 :  22:55:59  Show Profile  Reply with Quote
poly isnt required in a wooden viv its only required when putting the mat under a faun, rub or glass tank as will insulate and direct heat into the tank etc rather than lettin excess heat escape elswhere

paul

dogs:1.1.0 cookie, scrappy
rabbit:0.1.0 bluebell
beardies:1.1.0 spike, sunshine
corns:1.0.0 sid
Go to Top of Page

Kellog
the nice one

United Kingdom
7308 Posts

Posted - 31/03/2010 :  04:57:46  Show Profile  Reply with Quote
I am the same as Morph, have the probe for both my stat and digital thermometer weighed down with rocks touching the heatmat, and then the heatmat covered with a very small layer of substrate....deepening it to burrowing level over in the cool end.

I am probably wrong but the fact that the cool end was getting too hot could very well be to do with the bulb you are using as I know I had that when I was heating the viv with a bulb and not a heatmat (not my choice ) and I am so glad I have now changed over to a heatmat, stat and digital thermometer....with a low watt bulb.

What temps are you getting each end? (sorry if this has been mentioned in previous thread, havent checked it)

xxx



Go to Top of Page

headlow
Hatchling

130 Posts

Posted - 31/03/2010 :  09:40:19  Show Profile  Reply with Quote
When the weather was warmer the cold end was getting to just over 25 celsius. I put a couple extra vents in, and it has helped a bit, but I'm just concerned about how high the temps would get come the summertime.

Gonna go a bit off topic here, but I installed these it Sid's tank over last weekend....
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=220526653994

fantastic for night time viewing :)

1.0.0 Snow Corn
Go to Top of Page

morph2010
Egg

United Kingdom
97 Posts

Posted - 31/03/2010 :  17:04:34  Show Profile  Reply with Quote
quote:
Originally posted by headlow

When the weather was warmer the cold end was getting to just over 25 celsius. I put a couple extra vents in, and it has helped a bit, but I'm just concerned about how high the temps would get come the summertime.

Gonna go a bit off topic here, but I installed these it Sid's tank over last weekend....
http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=220526653994

fantastic for night time viewing :)




just looked at them lights they look cool as

have been scratching my brains for ages of the idea of putting a light in harley's viv theese look just the job!!

how bright are they? i'd rather have a low watt light source

1 Harley, Anery corn (not sure on age!)
1 Amber, Mad as a hatter springer 7yrs
8 ft fish tanks loads of fishys
1 Bobby, Cat 2yrs


Go to Top of Page

headlow
Hatchling

130 Posts

Posted - 31/03/2010 :  23:16:53  Show Profile  Reply with Quote
just looked at them lights they look cool as

have been scratching my brains for ages of the idea of putting a light in harley's viv theese look just the job!!

how bright are they? i'd rather have a low watt light source
[/quote]


They are adjustable. I have them on a medium setting and it's plenty bright enough to see

1.0.0 Snow Corn
Go to Top of Page

morph2010
Egg

United Kingdom
97 Posts

Posted - 02/04/2010 :  16:31:27  Show Profile  Reply with Quote
looks like there on my next shopping list!!!

1 Harley, Anery corn (not sure on age!)
1 Amber, Mad as a hatter springer 7yrs
8 ft fish tanks loads of fishys
1 Bobby, Cat 2yrs


Go to Top of Page
  Previous Topic Topic Next Topic  
 New Topic  Reply to Topic
 Printer Friendly
Jump To:
The Corn Snake Forum © 2000-11 thecornsnake.co.uk Go To Top Of Page
Snitz Forums 2000